Taubmans & White Knight
2 Manual tint machine instructions
9 Manual tint machine maintenance
11 Automatic tint machine instructions
16
25
2 Manual tint machine instructions
9 Manual tint machine maintenance
11 Automatic tint machine instructions
16
25
Step 1
Prepare label and can, ensuring the correct base has been chosen.
Step 2
Pull down lock handle and rotate carousal to the required tint canister to be dispensed.
Step 3
Set gauge to tint formula. For more information refer to ‘Setting the gauge’.
Step 4
To prime the pump, lift red handle up down up twice, ensuring it is left in the top position.
Step 5
To dispense, open arm fully.
Step 6
Pull red handle down completely until dispensing stops. Close arm.
Step 7
Repeat step 2 to 6 until dispense complete.
Step 8
Once dispensing is complete, make sure all gauges are returned to bottom position in preparation for next person to use machine.
Each tint canister has two dispensing gauges.
The black gauge can dispense from 16N to 2Y in steps of two.
The red gauge can dispense from .25N to 16N in steps of .25.
C 0Y 27N is dispensed by a combination of:
gauge 26N + Red gauge 1N = 27N
BlackPush black button and lift black gauge to 26. Release black button.
The black gauge can dispense from 16N to 2Y in steps of two.
Push red button and lift to 1N. Release red button.
The red gauge can dispense from .25N to 16N in steps of .25. Total set for dispense is now 27N.
Step 1
Fill canisters.
• Stir colourant for 2 minutes before filling canister.
• Double check correct colourant is going into correct canister.
• Do not fill up to the top of the canister. Leave a 2cm gap.
Step 2
Wipe down stand, canisters, and pumps with moistened cloth.
Step 3
Check and clean nozzle outlets for dried colourants.
Step 1
Select ‘Options’.
Step 2
Select ‘Dispenser maintenance’.
Step 3
Select ‘Dispenser maintenance’ window to bring to the front.
Step 4
Check tint levels in canisters. Anything under half full should be filled.
Step 5
Stir tint before filling canister.
Step 6
Fill up to 25mm from the top.
Step 7
Select ‘Tint’ and add.
Step 8
1. Enter amount added e.g. 1litre then select ‘OK’.
2. Repeat for all and then push exit.
Step 1
Place purge pot onto platform.
Step 2
Select Options.
Step 3
Select Dispenser Maintenance.
Step 4
1. Select Dispenser Maintenance screen to bring to front.
2. Select Purge all.
Step 5
Check tint is dispensing. Once complete remove purge pot.
Finish
Step 1
Select Options.
Step 2
Select Dispenser Maintenance.
Step 3
Select Dispense maintenance window to bring to front.
Step 4
1. Select Configuration.
2. Select Machine details.
Step 5
Drop platform to bottom.
Step 6
Pull cover plate forward and drop down front.
Step 7
Select Open nozzle.
Step 8
Unscrew sponge holder and pull out
Step 9
Remove sponge.
Step 10
Clean holder.
Step 11
Insert new sponge.
Step 12
Insert sponge holder and tighten.
Step 13
Select Close nozzle.
Step 14
Once nozzle has closed successfully select OK.
Step 15
Close cover plate.
Step 16
Select OK.
Step 1
Press and hold clamping button until can clamp has opened fully.
Step 2
Open door by lifting handle.
Step 3
Pull out can tray until it stops.
Step 4
Place can in the middle of tray and secure handle to can using the rubber band located on front of mixer.
Note Pictured unit is suitable for paint cans between 1L and 10L. Plastic paint pails need a protective spacer placed on top of the pail to stop damage to the pail when mixing. Spacers stored on the top of the mixers.Step 5
1. Push tray in until tray slots into place.
2. Close door.
Step 6
Push middle button to start mixing.
Note if can shakes loose press red emergency stop button.Step 7
Once mixer stops, push and hold clamp button until can clamp has fully opened.
Step 8
1. Open door and pull out can tray.
2. Remove rubber band.